Search Results

The preliminary design of a single engine business jet is presented. The airplane is intended to fill a market niche surrounded by several types of airplanes: single engine (piston and turboprop) and entry-level twin engine airplanes (turboprop and turbofan). The Williams-Rolls FJ44 turbofan engine, with a takeoff thrust rating of 1900 pounds, is chosen as the powerplant because of its low acquisition and maintenance costs. The airplane is designed to carry four persons and baggage 1500 n.m. with VFR reserves, and is intended to meet FAR 23 standards — including the 61 knot single engine stall speed requirement. A parametric analysis of wing aspect ratio, thickness, and taper is performed to determine the best planform from the standpoint of weight, cruise speed, and cost. Maximum cruise speed is estimated to be 371 knots and the airplane purchase price is estimated to be 1.98 million. These results indicate the airplane will satisfy intended market niche.

In two experiments, we examined the possibility that rearview mirror reflectivity influences drivers' perceptions of the distance to following vehicles. In the first experiment, subjects made magnitude estimates of the distance to a vehicle seen in a variable-reflectance rearview mirror. Reflectivity had a significant effect on the central tendency of subjects' judgments: distance estimates were greater when reflectivity was lower. There was no effect of reflectivity on the variability of judgments. In the second experiment, subjects were required to decide, under time pressure, whether a vehicle viewed in a variable-reflectance rearview mirror had been displaced toward them or away from them when they were shown two views of the vehicle in quick succession. We measured the speed and accuracy of their responses. Mirror reflectivity did not affect speed or accuracy, but it did cause a bias in the type of errors that subjects made.

NASS 80-88 passenger side impacts data were analyzed. Location of primary car damage using the CDC classification, the AIS for injury severity studies, and the interior contacts of the various body areas. Drivers alone, or with passengers were studied separately in both left and right side crashes. Direct impacts to the passenger compartment only are less frequent than to other CDC side zones. Driver interior contacts vary by body region but also by side impacted in the crash. The presence of an unrestrained front passenger appears to enhance driver injury level in left side crashes but the presence of a passenger, in right side crashes appears to moderate driver injury severity.

Originally written in 1976 and previously revised in 1983, The Maintenance Council (TMC) Recommended Practice RP-404B is intended to enhance the safety of motor carrier employees by providing guidance regarding the purchase and use of access systems on heavy truck and truck tractors. Compliance with the recommended practice is intended to permit anyone entering or exiting a cab to have three limbs in contact with the truck or truck-tractor at arty time. The scope of the recommended practice covers access systems to the cab and rear of cab areas of all types of heavy trucks and truck tractors, in contrast to Bureau of Motor Carrier Safety (BMCS) regulations which applies only to Cab Over Engine (COE) tractors. The Maintenance Council recommended practice also varies from the BMCS requirements in that it remains a design oriented document.

Intelligent Vehicle-Highway Systems (IVHS) improve the operation of cars and trucks on public roads by combining information technology with road transportation technologies. The basic ideas about IVHS are by no means new but a number of converging forces have encouraged significant IVHS development in North America recently. Based on the results of a Delphi survey to project realistic future scenarios, both applied and fundamental research agenda are being formulated in a Michigan-based IVHS program to push the IVHS technologies for advanced motorist information systems and for backup vehicle controls under emergency conditions. The scope of the research agenda includes social/human elements as well as hardware and software technological systems. The Michigan research program is expected to contribute to the development of IVHS in North America, both technically and institutionally.

This paper discusses the recent growth in aluminum wheel popularity and the problems associated with maintaining the wheel's appearance and corrosion protection. The various options in wheel coatings are then described as well as the adverse wheel environment. Finally, the variables affecting wheel corrosion resistance are explained and the testing that is undertaken to evaluate the performance characteristics of the wheel coating.

The role of automotive electronics in light duty vehicles is continuing to expand rapidly. In this paper an overview of a 1986 Delphi forecast of major trends is presented. Trends discussed include electronics as a fraction of vehicle and component cost and projections of basic vehicle features supported by electronic technology. In addition, basic trends in diagnostics and multiplexing are presented. Several issues in support of automotive electronics are discussed, including the systems approach to vehicle engineering, the importance of developing a proper market strategy, and the continued major role of energy economics. The Delphi forecasting technique and its governing concepts are reviewed as a method to predict the future of automotive technology.

Designing trucks for good ride characteristics is a challenge to the engineer, given the many design constraints imposed by requirements for transport productivity and efficiency. The objective of this lecture is to explain why trucks ride as they do, and the basic mechanisms involved. The response of primary interest is the vibration to which the driver is exposed in the cab. Whole-body vibration tolerance curves give an indication of how those vibrations are perceived at the seat; however, ride studies have shown that visual and hand/foot vibrations are also important to the perception of ride in trucks. The ride environment of the truck driver is the product of the applied excitation and the response properties of the truck. The major excitation sources are road roughness, the rotating tire/wheel assemblies, the driveline, and the engine.

This paper summarizes the results of Phase 1, Concept Definition, of the AATD program and identifies the reasons such a new test device is needed. The following areas are addressed: 1) injury priority from accident data; 2) current dummy design, use, and potential improvements; and 3) technical characteristics and design concepts for a new AATD, its data processing, and its certification systems.

Analytical methods are used to evaluate the braking and steering performance of tractor-semitrailer, truckfull trailer, double, and triple combinations that have mechanical properties corresponding to current design and usage practices in the United States.

A cylindrical combustion bomb with dynamic charging system and electro-hydraulic sampling valve is used to study the effects of turbulence on hydrocarbon (HC) emissions from a quench layer and from artificial crevices. The turbulence level is varied by changing the delay time between induction of combustible charge and ignition. Propane-air mixtures were studied over an initial pressure range of 150 to 500 kPa and equivalence ratios of 0.7 to 1.4. Sampling valve experiments show that quench-layer fuel hydrocarbons are extensively oxidized within 5 ms of flame arrival under laminar conditions and that turbulence further reduces the already low level. Upper limit estimates of the residual wall layer HC concentration show that residual quench layer hydrocarbons are only a small fraction of the exhaust HC emission.

Rolling resistance measurements were made on a sample of twenty-four retreaded and four new truck tires spanning a variety of constructions, tread patterns and tread depths. Examination of the results showed some relationship between three construction features and the resulting rolling resistance values. These are (a) Radial or bias carcass construction, (b) Tread pattern, and (c) Tread depth. The latter two characteristics can over-ride radial or bias construction effects. The effect of tread compound could not be analyzed in this limited test program. Good quality retreaded truck tires can exhibit comparable rolling resistance with new truck tires.

A method has been developed for calculating the internal temperature distribution in an aircraft tire while free rolling under load. The method uses an approximate stress analysis of each point in the tire as it rolls through the contact patch, and from this stress change the mechanical work done on each volume element may be obtained and converted into a heat release rate through a knowledge of material characteristics. The tire cross-section is then considered as a body with internal heat generation, and the diffusion equation is solved numerically with appropriate boundary conditions at the wheel and runway surface. Comparisons with buried thermocouples in actual aircraft tires shows good agreement.

Lap-shoulder belt effectiveness has been indicated by many authors, however there is minimal information on the more severe injuries to lap-shoulder belted car occupants. This paper presents details of 15 lap-shoulder belted occupants in frontal collisions and 24 lap-shoulder belted occupants in side impact collisions. Case descriptions of these crashes are presented, each including vehicle, environmental and injury details.

Properties of the human neck which may influence a person's susceptibility to “whiplash” injury during lateral impact have been studied in 96 normal subjects. Subjects were chosen on the basis of age, sex, and stature and data were grouped into six primary categories based on sex (F, M) and age (18-24, 35-44, 62-74). The data include: measures of head, neck and body anthropometry in standing and simulated automotive seating positions, three-dimensional range of motion of the head and neck, head/neck response to low-level acceleration, and both stretch reflex time and voluntary isometric muscle force in the lateral direction. Reflex times are found to vary from about 30 to 70 ms with young and middle aged persons having faster times than older persons, and females having faster times than males. Muscle strength decreases with age and males are, on the average, stronger than females.

Although over 800 references to child and infant anthropometry are in the literature, most have limited validity and application to current populations. Functional measures required by industry and government for federal safety standards for design of dummies, child products, furniture, or protective devices such as restraint systems have either been incomplete, inadequate, or nonexistent. Some of the limitations influencing validity of existing data have been outlined for the potential user. As a start toward obtaining necessary functional anthropometric data, The University of Michigan is currently conducting a study sponsored by the U.S. Consumer Product Safety Commission to obtain valid nationwide measurements on a representative U.S. population from birth to age 12 years. In this study some 41 measurements, including many functional measures, as well as seated and supine whole-body centers of gravity, are being taken utilizing a new automated anthropometric minicomputer system.

APPLICATION of nuclear energy for civilian automotive uses has possibilities, these authors say. Nuclear power for automotive applications, they feel, is technically feasible now where size and weight are not prime considerations; where size and weight are major parameters, discoveries of new materials for construction of nuclear-power reactors must be made. New materials are needed for reactor fuels, heat extractants, neutron reflectors, reactor construction materials, controls, and radiation shields which must have unique nuclear properties in addition to conventional engineering properties. This paper presents nuclear automotive propulsion devices in terms of technologies now available. The necessary radiation-shielding mass and weight requirements are presented for an ideal point-source nuclear-heat-power engine.